Bluetooth: btusb: Check for unexpected bytes when defragmenting HCI frames

Some Barrot based USB Bluetooth dongles erroneously send one extra
random byte for the HCI_OP_READ_LOCAL_EXT_FEATURES command. The
consequence of that is that the next HCI transfer is misaligned by one
byte causing undefined behavior. In most cases the response event for
the next command fails with random error code.

Since the HCI_OP_READ_LOCAL_EXT_FEATURES command is used during HCI
controller initialization, the initialization fails rendering the USB
dongle not usable.

> [59.464099] usb 1-1.3: new full-speed USB device number 11 using xhci_hcd
> [59.561617] usb 1-1.3: New USB device found, idVendor=33fa, idProduct=0012, bcdDevice=88.91
> [59.561642] usb 1-1.3: New USB device strings: Mfr=0, Product=2, SerialNumber=0
> [59.561656] usb 1-1.3: Product: UGREEN BT6.0 Adapter
> [61.720116] Bluetooth: hci1: command 0x1005 tx timeout
> [61.720167] Bluetooth: hci1: Opcode 0x1005 failed: -110

This patch was tested with the 33fa:0012 device. The info from the
/sys/kernel/debug/usb/devices is shown below:

T:  Bus=01 Lev=02 Prnt=02 Port=02 Cnt=01 Dev#= 12 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=33fa ProdID=0012 Rev=88.91
S:  Product=UGREEN BT6.0 Adapter
C:* #Ifs= 2 Cfg#= 1 Atr=c0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms

Now the device is initialized properly:

> [43.329852] usb 1-1.4: new full-speed USB device number 4 using dwc_otg
> [43.446790] usb 1-1.4: New USB device found, idVendor=33fa, idProduct=0012, bcdDevice=88.91
> [43.446813] usb 1-1.4: New USB device strings: Mfr=0, Product=2, SerialNumber=0
> [43.446821] usb 1-1.4: Product: UGREEN BT6.0 Adapter
> [43.582024] Bluetooth: hci1: Unexpected continuation: 1 bytes
> [43.703025] Bluetooth: hci1: Unexpected continuation: 1 bytes
> [43.750141] Bluetooth: MGMT ver 1.23

Link: https://github.com/bluez/bluez/issues/1326


Signed-off-by: Arkadiusz Bokowy <arkadiusz.bokowy@gmail.com>
Tested-by: Arkadiusz Bokowy <arkadiusz.bokowy@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>